This document outlines Laerdal' s requirements for a dedicated simulation network setup for your Laerdal simulation equipment. This document is regularly updated.

소프트웨어

SimPad PLUS v. 9.0.7

222.4 MB
2025/07/04

New in this release:

Fix for an issue where the simulator would cough twice, instead of once, and show a warning about network quality on the SimPad after connecting using Bluetooth Low Energy (BLE).
Fix for an issue where the SimPad PLUS 2, Link Box PLUS 2 and CPUM 2 based simulators were frequently dropping connection to enterprise networks with a signal strength of 65 dBm or less.
Fix for an issue where the GUI controls for tracheostomy were not available for SimNewB if starting a session straight after a software update.
Fix for an issue where it was not possible to calibrate the blood pressure cuff on the Nursing Anne Simulator
After introduction of the banner notifying users that the network quality is poor, several users have complained that the banner is appearing too frequently – also when network quality is sufficient. In response to this feedback, we have adjusted the triggers for this message so that it should appear only when relevant.

Fixes for SimBaby:

Fix for an issue where the tracheostomy feature was in some cases not available in SimPad or LLEAP UI when connected to a SimBaby Tracheostomy. This issue has been reported multiple times over the last few years, and in this version the cause of this intermittent issue has been identified and fixed.
Fixed issue where SimBaby with CPU Module 2 would in some cases end up with a red light after upgrading.

Fixes for SimNewB:

Fixed issue where opening breath during lung recruitment was not working as intended. The airway valves were partially open during initial ventilation. This fixed was fixed so that airway valves stay closed during the initial ventilation, and gradually open through the required number of ventilations.
The version contains firmware to fix missing calibration functionality on start up in some circumstances for the chest rise pump on SimNewB. This solves an intermittent issue where breathing would not be very visible.
Fixed issue where the banner indicating that SimPad and simulator were on different versions would sometimes persist after a simulator update to compatible version.

Network and simulator connectivity improvements:

Fixed issue where short Wi-Fi network glitches caused long reconnect times.
Fixed issue where the banner notifying users of Wi-Fi connection lost did not appear.
Fixed issue where the simulator did not fully disconnect from SimPad.
Fixed issue were turning off the simulator triggered a network quality banner.
Fixed issue where SimPad froze when trying to reconnect to a simulator after an upgrade.
Fixed issue were disconnecting from Standardized Patient took a long time

Note:

Simulator update

Updating Nursing Anne Simulator, SimNewB and SimBaby can take up to 20 minutes. Wait for a steady green light on the manikin.
Resusci manikins the update can takes up to 5 minutes.

SimPad PLUS 2 v. 9.0.7

346.8 MB
2025/07/04

New in this release:

Fix for an issue where the simulator would cough twice, instead of once, and show a warning about network quality on the SimPad after connecting using Bluetooth Low Energy (BLE).
Fix for an issue where the SimPad PLUS 2, Link Box PLUS 2 and CPUM 2 based simulators were frequently dropping connection to enterprise networks with a signal strength of 65 dBm or less.
Fix for an issue where the GUI controls for tracheostomy were not available for SimNewB if starting a session straight after a software update.
Fix for an issue where it was not possible to calibrate the blood pressure cuff on the Nursing Anne Simulator
After introduction of the banner notifying users that the network quality is poor, several users have complained that the banner is appearing too frequently – also when network quality is sufficient. In response to this feedback, we have adjusted the triggers for this message so that it should appear only when relevant.

Fixes for SimBaby:

Fix for an issue where the tracheostomy feature was in some cases not available in SimPad or LLEAP UI when connected to a SimBaby Tracheostomy. This issue has been reported multiple times over the last few years, and in this version the cause of this intermittent issue has been identified and fixed.
Fixed issue where SimBaby with CPU Module 2 would in some cases end up with a red light after upgrading.

Fixes for SimNewB:

Fixed issue where opening breath during lung recruitment was not working as intended. The airway valves were partially open during initial ventilation. This fixed was fixed so that airway valves stay closed during the initial ventilation, and gradually open through the required number of ventilations.
The version contains firmware to fix missing calibration functionality on start up in some circumstances for the chest rise pump on SimNewB. This solves an intermittent issue where breathing would not be very visible.
Fixed issue where the banner indicating that SimPad and simulator were on different versions would sometimes persist after a simulator update to compatible version.

Network and simulator connectivity improvements:

Fixed issue where short Wi-Fi network glitches caused long reconnect times.
Fixed issue where the banner notifying users of Wi-Fi connection lost did not appear.
Fixed issue where the simulator did not fully disconnect from SimPad.
Fixed issue were turning off the simulator triggered a network quality banner.
Fixed issue where SimPad froze when trying to reconnect to a simulator after an upgrade.
Fixed issue were disconnecting from Standardized Patient took a long time

Note:

Simulator update

Updating Nursing Anne Simulator, SimNewB and SimBaby can take up to 20 minutes. Wait for a steady green light on the manikin.
Resusci manikins the update can takes up to 5 minutes.

SimPad PLUS v. 9.0.4.53

2025/01/10

Important Notes:

From 9.0.0 the use of SimLink (Ad Hoc network that lets devices communicate directly when there is no wireless network available) is not supported anymore. For more information, see Removal of support for Ad-Hoc Network connections for LLEAP and SimPad.

Bug fixes in this release:

Fix for an issue introduced in version 9.0.0 where the SimPad would freeze/become unresponsive and require a restart in the following cases.

Known issues in 9.0.4

SimPad PLUS SkillReporter not able to connect to Resusci Anne MK1.
Support for custom sound is missing.
Not able to connect to connect to hidden network with PEAP-MSCHAPv2.

Other Fixes since 9.0.0

Fix for an issue where the Link Box would appear to be in flight mode when connected to the Simulator Firmware and Network Wizard (SFNW) in LLEAP.
Fix for an issue where a SimPad or Link Box that had been upgraded via Simulator Firmware and Network Wizard (SFNW) in LLEAP was not discoverable unless restarted.
Fix for an issue where the VCA would not work right after a software upgrade unless devices was restarted.
Fix for SimPad Plus and Link Box PLUS is not discoverable in Simulator Firmware & Network Wizard right after upgrade.
Automatic reconnection to previously used Wi-Fi network on device start.
Increased USB file transfer speed for SimPad.
Improved high temperature warnings, if SimPad or simulator gets to hot during use.
Refresh of system settings menu to move most used items towards the top of the menu.
Updates to on-screen prompts when starting a SimPad for the first time.
Security updates.
Improved simulator sounds for Link Box based simulators.
Fix for an issue where simulator would not always cough to indicate it had started.
Fix for an issue where pacing would in some cases be inconsistent when using SimPad with Resusci Anne Advanced Skill Trainer.
Icon for idioventricular heart rhythm on the SimPad changed as it was not correct, manikins capable for running idioventricular rhythms are SimBaby, SimNewB and NAS.
Fix for an issue where VCA would sometimes disconnect during use.
Fix for an issue where Sounds Trainer did not play lung sounds.
Fix for VCA issues.
Fix for custom Theme.
Fix for pacing.

Note:

Simulator update

Updating Nursing Anne Simulator, SimNewB and SimBaby can take up to 60 minutes. Wait for a steady green light on the manikin.
Resusci manikins the update can takes up to 5 minutes.

SimPad PLUS 2 v. 9.0.4.53

2025/01/10

Important Notes:

From 9.0.0 the use of SimLink (Ad Hoc network that lets devices communicate directly when there is no wireless network available) is not supported anymore. For more information, see Removal of support for Ad-Hoc Network connections for LLEAP and SimPad.

Bug fixes in this release:

Fix for an issue introduced in version 9.0.0 where the SimPad would freeze/become unresponsive and require a restart in the following cases.

Known issues in 9.0.4

SimPad PLUS SkillReporter not able to connect to Resusci Anne MK1.
Support for custom sound is missing.
Not able to connect to connect to hidden network with PEAP-MSCHAPv2.

Other Fixes since 9.0.0

Fix for an issue where the Link Box would appear to be in flight mode when connected to the Simulator Firmware and Network Wizard (SFNW) in LLEAP.
Fix for an issue where a SimPad or Link Box that had been upgraded via Simulator Firmware and Network Wizard (SFNW) in LLEAP was not discoverable unless restarted.
Fix for an issue where the VCA would not work right after a software upgrade unless devices was restarted.
Fix for SimPad Plus and Link Box PLUS is not discoverable in Simulator Firmware & Network Wizard right after upgrade.
Automatic reconnection to previously used Wi-Fi network on device start.
Increased USB file transfer speed for SimPad.
Improved high temperature warnings, if SimPad or simulator gets to hot during use.
Refresh of system settings menu to move most used items towards the top of the menu.
Updates to on-screen prompts when starting a SimPad for the first time.
Security updates.
Improved simulator sounds for Link Box based simulators.
Fix for an issue where simulator would not always cough to indicate it had started.
Fix for an issue where pacing would in some cases be inconsistent when using SimPad with Resusci Anne Advanced Skill Trainer.
Icon for idioventricular heart rhythm on the SimPad changed as it was not correct, manikins capable for running idioventricular rhythms are SimBaby, SimNewB and NAS.
Fix for an issue where VCA would sometimes disconnect during use.
Fix for an issue where Sounds Trainer did not play lung sounds.
Fix for VCA issues.
Fix for custom Theme.
Fix for pacing.

Note:

Simulator update

Updating Nursing Anne Simulator, SimNewB and SimBaby can take up to 60 minutes. Wait for a steady green light on the manikin.
Resusci manikins the update can takes up to 5 minutes.

SimPad PLUS 8.7.0

2023/11/01

Updates in this release:

Laerdal Connect integration.
Patient Monitor color control
Patient Monitor toggle peripheral temperature from SimPad.
Auscultation button for SimJunior.

Bug fixes in this release:

BP Trainer not detected.
SimBaby Brachial pulse not getting absent intil BP = 0.
VT type 1&2 remame to VT Mono&Poly.
Wifi: GUI for hidden Enterprise PEAP network.

Note:

Simulator update

Updating Nursing Anne Simulator, SimNewB and SimBaby can take up to 60 minutes. Wait for a steady green light on the manikin.
Resusci manikins the update can takes up to 5 minutes.

SimPad Theme Editor 1.3.1

3.8 MB - English
2021/10/11

SimPad Theme Editor is a PC software tool for creating Themes for the SimPad system when operated using the Manual Mode. The program allows you to easily make new Themes with States and Interventions. The new version is no longer an online tool. Please download and install SimPad Theme Editor localy on your computer.

Dependency on Microsoft Silverlight removed, so that Theme Editor can be used without Silverlight installed.
Minor changes to user interface.

SimPad PLUS 7.4.5

2021/06/11

Changes in this release:

Session logfiles on Standardized patient are not stores if user quits session.

Changes from version 7.4.0:

Nursing Anne Simulators will have a new option in Session Information to change the default age and gender of the manikin (per now it only affects prerecorded sounds).

Age and Gender Setup button is only visible when connected to a Nursing Anne Simulator .

Voice Conferencing Application (VCA) improvements.

Occasional aliasing on VCA has been improved.
Prerecorded sounds will in some cases sound loud through the instructor headset, a button to automatically mute instructor headset when playing prerecorded sounds has been added.

Fix Vocal sound on SimMan ALS.
Fix flow fraction score for BLS Instructor.
Fixed issue with Nursing Anne Simulator, SimNewB and SimBaby where they would sometimes not connect after running first session.
Corrected problem where SimPad would sometimes not connect to internet enabled services such as Laerdal Scenario Cloud.
Fixed ShockLink update issue where some devices would fail to update to newest version.

Note:

Updating to Windows 10?

Using SimLink or Custom ad hoc network on SimPad, and considering upgrading to Windows 10 on your computers for Laerdal Patient Monitor?
- Microsoft ended their support for this type of network with the release of Windows 8. From Windows 10 the equipment will need to use a separate simulation network.

Windows 7

Patient monitor 8.0.0 and newer will not support Windows 7

Updating Nursing Anne Simulator, SimNewB and SimBaby take up to 20 minutes. Wait for a steady green light on the manikin.
Resusci manikins are updated with new firmware, the update takes up to 5 minutes.

SimView Downloads

2017/11/24

Use this link to download latest software to SimView

SimView Mobile Downloads

2017/11/24

Use this link to download latest software to SimView Mobile

Session Viewer Downloads

2017/11/09

Use this link to download latest software to Session Viewer

심폐소생술 CPR 심폐소생술 전문인명소생술 AHA 교육자료 교육용 AED	보건의료 교육 환자 시뮬레이터 마네킹 술기 교육 모델 정맥로 확보	시나리오 & 환자케이스 vSim® for Nursing Fundamentals	기도 관리 감염방지장비 인공호흡 흡인기 주문식 라벨
척추 고정 경추고정대 머리고정장치 척추고정대	심실 제세동기 부품과 액세서리 교육용 AED

심폐소생술

보건의료 교육

시나리오 & 환자케이스

기도 관리

척추 고정

심실 제세동기 부품과 액세서리

다운로드: SimPad PLUS

DFU

문서

소프트웨어