HomeDownloadsDownloads for LLEAP - Laerdal Learning Application

Downloads for LLEAP - Laerdal Learning Application



Directions for Use

SimStart User Guide

3.4 MB - English
10/01/20

Simulated AED or Monitor Defibrillator training functionality available in Laerdal Learning Application- LLEAP
Quick Guide WiFi setup

1.2 MB - English
24/06/19

Session Viewer - User Guide

2.7 MB - Multilingual
10/07/15

Documents

Laerdal Network Requirement Document Rev R

1.1 MB - English
26/10/22

This document describes the requirements for setting up a network on pre-existing infrastructure specifically for Laerdal simulation devices.

Software

SimDesigner v 8.5.1 Patch

2.8 MB
01/03/23

Changes in this release:

  • Fix for phase without state causes software crash.
  • Fix for software crash when using conditions in drug.
  • Fix for issue when double clicking on window.
  • Fix for etCO2, etCo2 can't be set if unit is not mmHg.
  • Fix for user interface when using zoom feature
Laerdal Learning Application (LLEAP) v. 8.5.0

1 467.3 MB
19/01/23

Changes in this release:

  • LLEAP.
    • If a theme or scenario has media files included, these files will now be visible directly in the Transfer Media dialogue in LLEAP.
    • Renaming of SimMan 3G simulators has been made easier by moving it to Customize simulator in the Simulator Firmware & Network Wizard. Previously the user had to select Configure SimMan 3G Network and walk through all the steps to configure WiFi to rename the simulator.
    • For SimNewB a checkbox to register that the simulator has been intubated has been added.
    • LLEAP can now run on Windows 10 computers where FIPS (Federal Information Processing Standard) is enabled. LLEAP has been set to be exempted and is not validated against FIPS requirements
    • Bug fixes:
      • Fix for an issue where it was not possible to upgrade SimPad to the latest version using the Simulator Firmware and Network Wizard.
      • Fix for Stomach “Inflate” that appeared on none suported simulators, only supported by SimJunior.
      • Fix for button to disable and enable stomach distention that appeared for unsupported simulators, this button is now only available for SimJunior which has this feature.
      • Fix for an issue on SimMan 3G where pacing did not affect the pulse.
      • Fix for an error preventing Windows 10 updates to be run on SimMan simulators.
      • Fixed an issue where the name for the “No” vocal sound had a misleading name in the French translation.
      • Fixed range for Sinus 60 year range, now limited to 20-200.
      • Fix for scenarios with Timer, the count down did not work properly.
  • Patient Monitor.
    • Bug fixes:
      • Fix for an issue where the Patient Monitor would reconnect to a simulator during shutdown.
      • SP02 can now be turned on from the Patient Monitor.
      • Fix for PM sometimes get covered by a box.
  • SimMan 3G bug fixes.
    • Fix for an issue where SimMan 3G simulators would not connect to open wireless networks.
    • Fix for an issue on SimMan 3G where pacing did not affect the pulse .
    • Fix for an error preventing Windows 10 updates to be run on SimMan 3G simulators.
Laerdal Patient Monitor v. 8.5.0

821.1 MB
18/01/23

Changes in this release:

  • Bug fixes:
    • Fix for an issue where the Patient Monitor would reconnect to a simulator during shutdown.
    • SP02 can now be turned on from the Patient Monitor.
    • Fix for PM sometimes get covered by a box.
LLEAP Patch for 7.3.0

0.4 MB - English
28/07/21

LLEAP Patch for 7.3.0, for older SimMan 3G who can't use LLEAP 8.0

 

This update is supplied to fix an issue where chest rise and lung sounds ceases on the SimMan 3G when used with ASL 5000 using a ventilator setting of PEEP 2 cm H2O or greater. The issue can also be resolved by upgrading to LLEAP 8.0.0. This patch should only be used if upgrade to 8.0.0 is not possible, e.g if using older SimMan 3G with XP embedded which is not supported on LLEAP 8.0.0 and onwards.

Important: ASL 5000 plugin needs to be uninstalled before patch installation and reinstalled afterwards. Remember to back up custom lung models when prompted during uninstall process and import again during install process after upgrade to patch.

Note:

    SimMan 3G updater might need several tries before the patch is installed on simulator
Laerdal Learning Application (LLEAP) v. 7.3.0

1 526.9 MB
16/03/21

Important:

 

Changes in this release:

  • New Device Connection Manager (DCM) application to manage network configurations more efficiently on multiple manikins.
  • Enhanced support for Enterprise Network Security from SFNW & for SimMan3G with Wifi USB adapter.
  • Fixed an issue where SimMan3G system time was not synced.
  • Improved simulator connection on networks with high latency.
  • Included WiFi driver to LLEAP installer (for SOM on SimMan3G).
  • Fixed an issue where the simulation wouldn't use the wanted simulation profile unless explicitly selected. Could lead to using wrong units and similar problems.
  • LLEAP supports transport layer security (TLS) 1.2 or greater for login to Scenario Cloud.
  • Fixed an issue causing help files not to work.

 

Note:

Updating to Windows 10?
  • Using SimLink or Custom ad hoc network on SimPad, and considering upgrading to Windows 10 on your computers for Laerdal Patient Monitor?
    • Microsoft ended their support for this type of network with the release of Windows 8. From Windows 10 on, the equipment will need to use a separate simulation network. Laerdal can help you connect all your simulation equipment to a dedicated network. Learn more and get started at Laerdal.com/Network.

Last LLEAP version supporting Windows 7
  • LLEAP 7.3 will be the last version that supports Windows 7.

Last version supporting old SimMan 3G family simulators

Due to end of life for Windows XP Embedded used on older SimMan3G simulators, LLEAP will no longer supported as of this version, this applies to the following simulators - unless they have been upgraded to use Windows 7:

  • SimMan3G simulators with serial numbers lower than 212-16140000
  • SimMan3G Essential simulators with serial numbers lower than 213-16140000
  • SimMan3G Essential Bleeding simulators with serial numbers lower than 214-1614000

Windows Update
  • Before installing LLEAP, to secure a successful installation, please make sure the PC is fully updated through Windows Update. If you have problems starting LLEAP after installation, please download and run Visual C++ 2015 redistributable from this location: Microsoft Visual C++ 2015 Redistributable Update 3. . Select and run vc_redist.x86 then try running LLEAP.
Laerdal PatientMonitor v. 7.3.0

932.6 MB
11/03/21

Important:

 

The Laerdal Patient Monitor software is compatible with LLEAP and SimPad.

Laerdal Patient Monitor software is included when you download LLEAP. This download allows you to install Laerdal Patient Monitor software without installing LLEAP on the same computer.

 

Changes in this release:

  • New version to align with LLEAP 7.3.0
  • General maintenance, bugfixes and improvements.

 

Note:

Updating to Windows 10?
  • Using SimLink or Custom ad hoc network on SimPad, and considering upgrading to Windows 10 on your computers for Laerdal Patient Monitor?
    • Microsoft ended their support for this type of network with the release of Windows 8. From Windows 10 the equipment will need to use a separate simulation network.
Windows 7
  • Laerdal Patient Monitor 7.3 will be the last version that supports Windows 7
Laerdal Learning Application (LLEAP) v. 6.8.1

1 225.5 MB
18/12/19

Changes in this release:

  • Simulator lost connection - Improving error message.
  • SimBaby - Improved trachostomy functionality to close Laryngospasm and open airways.
  • SimBaby - Fixed issue with Pharyngeal obstruction not showing in Instructor Application for a virtual simulator.
  • Themes - Now showing features related to available simulator.
  • SimJunior - Fixed issue where simualtor did not show in simulator list.
  • SimMom - Now possible to connect SimMom using Advanced option.
  • LLEAP - Fixed issue related to changeing vital signs before starting session.
  • LLEAP - Fixed issue related to application start.
  • SimMan 3G - Fixed an issue where changes to tracheostoma opening is logged for SimMan 3G which is not supporting it.
  • LLEAP - Fixed an issue where SessionViewer still shows state "Recording" if LLEAP selects to start a new session .
  • Stop compression event - Fixed an issue where stopping simulated compression did not result in a "Stop compression" even.

 

Changes since 6.8.0:

  • Added support for SimBaby with Tracheostomy.
  • Several improvements and adjustments to UI for SimNewB.
  • Added a Stopwatch function. Click on the time-field next to the Play/Pause button on the Session control window to show the Stopwatch window..
  • Added a new pre-recorded vocal sound “OK” for Adult(Male/Female) and Child.
  • Improved UI for Stomach distention function. Now have a separate “Release air” button. For SimJunior there is also a separate “Inflate” button.
  • Fixed an issue where LLEAP would sometimes crash when ending a session.
  • Fixed an issue where Tongue fallback was not working properly when running a scenario.
  • Fixed an issue where transitions of User Defined Variables would not always end up on the correct value.
Laerdal Patient Monitor v. 6.8.1

673.3 MB
18/12/19

The Laerdal Patient Monitor software is compatible with LLEAP and SimPad.

Laerdal Patient Monitor software is included when you download LLEAP. This download allows you to install Laerdal Patient Monitor software without installing LLEAP on the same computer.

New version to align with LLEAP 6.8.1

Changes in this release:

  • Defibrillator Monitor - Fixed issue with layout.
  • Patient Monitor Layout - Fixed issue with hidden buttons after minimizing application.
  • Metronom sound - Fixed issue where metronome sound did not start.
  • ECG AV Block - Fixed issue with wrong HR on high heart rates.
  • SimMom - Fixed issue where SimMom was listed twice in simulator list.

 

Changes since 6.8.0:

  • Simulated AED and Defibrillator monitor (SimStart) now have translated voice prompts.
  • Improved volume indicator on simulated AED/Defibrillator monitor.
  • Fixed an issue where the NIBP auto measurement would be triggered too often.
  • Fixed an issue where the NIBP measurement would sometimes be shown before activating the measurement.
  • Fixed an issue where some buttons would not show after minimizing the Patient Monitor window.
  • Fixed an issue where Patient Monitor in AED mode would sometimes crash.
SimView Downloads


24/11/17

Use this link to download latest software to SimView
SimView Mobile Downloads


24/11/17

Use this link to download latest software to SimView Mobile
Session Viewer Downloads


09/11/17

Use this link to download latest software to Session Viewer

© 2001-2023 Laerdal Medical. All Rights Reserved.